Napoleon Entice 50" Wall Mount Linear Electric Fireplace
A 49-11/16" wide, 16-15/16" high electric fireplace only 5-7/16" deep that hangs on the wall, recesses partway, or builds in flush. The Napoleon Entice NEFL50CFH-1 runs full, tall flames in 10 colours over an ember bed of acrylic crystals, reflects them in a flame panel for depth, and heats at up to 5,000 BTU/hr from a standard 120 V outlet with no venting. The remote is included. from $1,229.
Choose the 50" if you want a slim electric fireplace for a 49-11/16" wall space that plugs in today and can be built into the wall later: it hangs on its bracket from a 120 V outlet, or hard-wires into a 48-7/8" x 16" opening with 0" clearance at the sides and back. It suits a living room, bedroom or kitchen wall where a gas fireplace and its venting are not an option.
It is not right if you need it to heat a room on its own: the heater tops out at 1,465 W, about 5,000 BTU/hr, which supplements a room rather than replacing the furnace. It is indoor-only and not for bathrooms, it needs its own dedicated 15 A circuit with no extension cord, and any recessed install has to be hard-wired by an electrician.
Specifications
The fireplace measures 49-11/16" wide, 16-15/16" high and 5-7/16" deep, with a 45-13/16" x 11-15/16" glass, and weighs 52.2 lb (65.5 lb packed). Recessed, it needs a 48-7/8" wide by 16" high opening in a non-load-bearing wall, at least 4" deep for a partial recess or 6" deep, including the finish, for a full recess. Clearance to combustibles is 0" at the bottom, sides and back, with 4" from the top of the trim to a ceiling or mantel; keep curtains, furniture and bedding 36" from the front. Power is 120 VAC, 60 Hz, 1,465 W, on a dedicated 15 A grounded circuit.
How the 50" compares to the other Entice sizes
The Entice comes in 36", 42", 50", 60", 72" widths, all the same 16-15/16" high, 5-7/16" deep fireplace with the same 1,465 W heater, controls and installation options; only the width, glass and opening change. The 50" is from $1,229; the 36" from $759, the 42" from $959, the 60" from $1,539, the 72" from $1,749.
Features
- Hang it on the wall, recess it partway, or build it in flush — the side and top trims and side cover panels ship in the box
- Full, tall flames in 10 colours at four brightness levels and five speeds, reflected in a flame panel for a deeper look
- Ember bed in 10 colours, plus 11 matched flame-and-ember presets including a colour cycle
- Up to 5,000 BTU/hr heater with low and high settings, a built-in thermostat and a child-safety lockout — or run the flames with no heat
- Plugs into a standard 120 V outlet, no venting needed
- Remote control with a sleep timer up to 8 hours
Answers to common questions
Does it need a vent, a chimney or a gas line?
No. The Entice is electric and needs no venting, only power. Wall-mounted, it plugs into a grounded 120 V outlet on a dedicated 15 A circuit; recessed partway or fully, a qualified electrician removes the cord and hard-wires it to a 120 V, 15 A circuit. Extension cords and power strips are not allowed.
Can I recess it into the wall?
Yes. It hangs on the wall on its bracket, or recesses into a non-load-bearing 48-7/8" wide x 16" high opening framed at least 4" deep for a partial recess or 6" deep, including the finish, for a full recess. It needs 0" clearance at the bottom, sides and back, and 4" from the top of the trim to a ceiling or mantel. Recessed installs are hard-wired by an electrician.
How much heat does it put out, and can I run it without heat?
The heater makes up to about 5,000 BTU/hr (1,465 W) on a standard 120 V outlet, with low and high settings and a built-in thermostat that holds 64°F to 82°F. The flames and ember bed run with the heater off, so you can use it year-round, and the heater can be locked out from the remote.
What’s included, what’s required, and what’s optional?
-
Included in the box: Acrylic crystal media - small and medium crystals with an ember-bed strip; Remote control with a sleep timer; Side and top trims and side cover panels for a wall-mounted or partially recessed install; Wall mount bracket, bottom bracket, framing brackets and a hardware kit with cord covers; 2-year parts warranty.
-
Required to complete the installation, purchased separately: Electrical - a dedicated, grounded 120 V, 15 A circuit: an outlet within reach of the cord when wall-mounted, or a hard-wired connection by a qualified electrician when recessed; no extension cords; Framing - a non-load-bearing 48-7/8" wide x 16" high opening, at least 4" deep for a partial recess or 6" deep including finish for a full recess (recessed installs only); Finishing Material - drywall or other wall finish around and inside the opening, keeping the heater vents uncovered (recessed installs only).
-
Optional: A birch or driftwood log set, or glass embers in one of six colours - the fireplace runs on the crystals it ships with.
Can I change the flame and ember colours?
Yes. The flames and the ember bed each run in 10 colours or a colour cycle, and the remote also offers 11 matched flame-and-ember presets. Flame brightness has four levels and flame speed five, and the ember bed can glow at four brightness levels or fade in and out.
Where can it be installed?
Indoors only. It is approved for bedrooms, bed-sitting rooms and mobile homes, but not for bathrooms. Keep curtains, furniture and bedding 36" from the front, keep it out of high-traffic areas, and never block the heater vents.
How does the warranty work if I buy it online?
Napoleon covers the Entice with a 2-year premium warranty: the heater and blower, motors, switches, the remote and the LED lights are replaced free for two years, labour is covered in the first year, and light bulbs and fuses are not covered. The Torch Guys is an authorized Napoleon dealer, so the full factory warranty applies, and if you ever need a part we file the claim with Napoleon for you. Keep your invoice and the model and serial number.
Pro Portal
Dedicated Support
Best Price
Large Selection
Exclusive Deals
Priority Shipping
