Majestic Biltmore 36" Wood Burning Fireplace
Nothing between you and the fire but a firescreen. The Majestic Biltmore 36 (BILT36) is a factory-built open-hearth wood burning fireplace with a 36" W x 28-1/2" H firebox opening, listed to UL 127 and ULC-S610. It frames 45-1/2" wide by 59-3/4" high by 28" deep, runs on an 11-inch SL1100 Series chimney and ships with its grate, firescreen and attic insulation shield. Choose a Traditional or Herringbone interior panel in three colors above; from $2,019 for the fireplace alone.
Choose the Biltmore 36 if you want a real wood fire with a masonry look and no glass in the way. Pick stacked Traditional or angled Herringbone brick in Natural Gray, Black Onyx or Masonry Brown, and keep your options open: gas knockouts on both sides mean a vented gas log set can go in later.
It is not right for you if you want a long, linear flame behind fixed glass. The Biltmore 36 is a true open hearth, with a 36" x 28-1/2" opening and masonry-look panels that make the fire the centerpiece of the room.
Specifications
Frame it 45-1/2" wide by 59-3/4" high by 28" deep, with 53-1/2" of width for the outside air connection. Keep 1" at the back and sides, and the top standoffs may touch the header. The unit stands 59-1/4" high, 27-1/2" deep and 44-1/2" wide at the front, and weighs 356 pounds. The chimney is SL1100 Series, at least 18 feet straight from the base of the fireplace, 18.5 feet with one offset and 24 feet with two, and no more than 90 feet. The bottom of the opening sits 7-5/8" above the bottom of the fireplace, which sets how high a finished raised floor can go.
How the Biltmore 36 compares to the other Biltmore sizes
The Biltmore 36 is the smallest of the three widths, framed 45-1/2 inches wide around a 36" x 28-1/2" opening. The Biltmore 42 keeps the same opening height at 42" x 28-1/2" and frames 51-1/2 inches wide. The Biltmore 50 steps up to a 50" x 33" opening, frames 61-5/8 inches wide and needs a 20-foot chimney and two outside air kits. The Biltmore 36 starts from $2,019, the 42 from $2,519 and the 50 from $3,779.
Features
- Open hearth with a 36" W x 28-1/2" H firebox opening and no glass between you and the fire
- Six interior panel looks: Traditional or Herringbone brick in Natural Gray, Black Onyx or Masonry Brown
- Steel grate, safety firescreen, attic insulation shield and protective metal hearth strips come with it
- Burns on outside combustion air through one outside air kit on the left side; the inlet hood ships with the fireplace
- Knockouts on both sides for 1/2-inch gas pipe, so a vented gas log set up to 100,000 BTU/hr can go in now or later
- Works as a room divider, along a wall, across a corner or in an exterior chase, and may go in a bedroom
Answers to common questions
What chimney does the Biltmore 36 need, and is it included?
The chimney is sold separately. The Biltmore 36 uses SL1100 Series chimney, 11 inches inside and 13 outside, with a termination cap from the component list (see pg 39 in the installation manual). Plan on at least 18 feet of straight height from the base of the fireplace, 18.5 feet with one offset and return, 24 feet with two, and no more than 90 feet, with 2 inches of air space around the pipe. The cap sits at least 3 feet above the roof and 2 feet above any part of the roof within 10 feet. In Canada you also need a chimney air kit and an SLA10 adapter. Give us your chimney height and we will build the package.
What’s included, what’s required, and what’s optional?
-
Included in the box: 36" W x 28-1/2" H firebox opening; Steel grate; Safety firescreen; Outside air inlet hood (the 4-inch flex duct is sold separately); Attic insulation shield; Protective metal hearth strips; Dual gas knockouts; UL 127 and ULC-S610 listing; Hearth & Home Technologies limited warranty.
-
Required to complete the installation, purchased separately: Interior Panel - a Traditional or Herringbone refractory set that lines the firebox; the Biltmore 36 ships without one and needs it before the first fire; Venting - an 11-inch SL1100 Series chimney and a termination cap from the component list (see pg 39 in the installation manual); our team will build the package for your chimney height; Outside Air - 4-inch flex duct to connect the included inlet hood to the left side of the fireplace; Floor Protection - a non-combustible floor in front of the opening, 20 inches deep and 60 inches wide, insulated to R 1.03; Non-Combustible Finish - tile, stone, brick or similar facing below the top standoffs and over the metal front of the fireplace.
-
Optional: Glass or mesh doors, a vented gas log set, and the chimney air kit (required in Canada); outside Canada the fireplace needs none of them to burn wood.
Do I need outside air?
Yes. An outside air kit is used for combustion, and it installs on the left side of the fireplace. The inlet hood is in the box; the 4-inch flex duct is not. Keep the run short: 4-inch duct can run up to 20 feet, or up to 40 feet in 6-inch duct with a 4-to-6-inch adapter. Insulated flex helps reduce frost condensation, and the inlet closes to stop cold drafts when the fireplace is not in use.
How close can a mantel or side wall be?
A combustible mantel up to 12 inches deep goes at least 12 inches above the opening, and combustible trim that projects no more than 1-1/2 inches stays at least 6 inches above the decorative front. A non-combustible mantel can sit lower if the wall around it is built of non-combustible materials. Combustible side walls stay at least 24 inches from the opening; mantel legs and wall projections are charted in Figure 7.11 on page 35 of the installation manual. Inside the framing, keep 1" at the back and sides. Drapes and chairs stay at least 4 feet from the open front. Send us your plan if you want it checked. We're here to help!
What goes on the floor in front of it?
A non-combustible floor at least 20 inches deep in front of the opening and 12 inches past each side, so 60 inches wide, finished in tile, stone or another non-combustible material over insulation rated at least R 1.03. The two metal hearth strips in the box go under the front edge of the fireplace. With the fireplace on the floor, a finished raised floor can go up to 7-5/8", which is the bottom of the opening; for anything higher, the fireplace goes on a platform.
Can I put gas logs in it?
Yes. A certified vented gas log set or gas log lighter can go in, up to 100,000 BTU/hr, through the knockouts on either side for 1/2-inch iron pipe. The damper is locked fully open with gas logs in place, and the log set needs its own gas shutoff. For this width, 18" cement log sets are the size to look for. Call us and we will match one to your fireplace.
Do I need doors?
No. Doors are optional, and the Biltmore 36 burns with its firescreen closed. If you want them, choose only doors approved for this fireplace, shown in the optional accessories on this page, and run them fully open or fully closed while the fire is burning.
Does buying from The Torch Guys affect my Majestic warranty?
No. The Hearth & Home Technologies warranty covers Majestic products bought through an authorized dealer, and The Torch Guys is one. If you ever need to claim, we deal with the manufacturer on your behalf. The firebox and heat exchanger carry 10 years on parts and 3 on labor, cement refractory panels 2 years, and other parts 1 year.
Pro Portal
Dedicated Support
Best Price
Large Selection
Exclusive Deals
Priority Shipping
