Skip to content
FREE Shipping On Orders Over $399!

Ask An Expert

(410) 324-6322

Ask An Expert

(410) 324-6322

(410) 324-6322

Live Chat

Email Us

Hours:

Mon-Sat - 8am-10pm EST

Sunday - Closed

Hours: Mon-Sat - 8am-10pm EST
by Majestic Authorized Dealer

Majestic Mercury 32" Direct Vent Gas Fireplace

SKU MERC32IN
What's Included?

Here's what ships in the box and what you'll choose above before checkout. Not sure what you need? Call us at (410) 324-6322 and our team will spec the right setup.

✓ Included Standard
Six ceramic fiber logs
Glowing embers
Full firescreen front and hood
Up to 19,100 BTU/hr on natural gas or propane
IntelliFire electronic ignition
Battery backup (two D cell batteries, not included)
Tempered glass
Junction box, manual gas shut-off valve and flex connector, and 12 ft of control wire
Top vent collar, 4" x 6-5/8", and rear vent collar, 5" x 8"
🔧 Options
Above the Cart (select from dropdown)
Fuel Type: Natural Gas or Propane
Below the Cart (select from optional accessories section)
Remote Controls, Wall Switch, Fan Kit, Trim Kit
⚠️ Required to Complete Installation
Venting - SLP pipe off the top or DVP pipe off the rear, and a wall or roof termination sized for your run (see pg 56 in the installation manual).
Electrical - an unswitched 110-120 VAC circuit to the junction box.
Gas Line - a 1/2" gas line to the shut-off valve.
Original price $2,209.00 - Original price $2,313.00
Original price
$2,209.00
$2,209.00 - $2,313.00
Current price $2,209.00

About This Product

Majestic Mercury 32" Direct Vent Gas Fireplace

The Majestic Mercury 32" is a direct vent gas fireplace with six ceramic fiber logs, glowing embers and a full firescreen front and hood standard: up to 19,100 BTU/hr on natural gas or propane, IntelliFire electronic ignition with battery backup, a 27-3/16" x 18-1/16" tempered glass opening, a 37" wide, 34-3/4" high and 16-1/4" deep framed opening and a choice of top or rear vent, from $2,209.

Choose the Mercury 32" if you want a traditional log fire with no front or media to pick: the logs, embers, front and hood all come with it. It vents off the top or the rear, so you can pick whichever suits your wall or roof. With only 1/2" of clearance at the back and sides and no raised hearth, it frames tightly into a wall, and it is also certified for bedrooms.

It is not right for you if you are looking for a linear fire on a bed of glass. The Mercury 32" sets its flames among six ceramic fiber logs over glowing embers, for a traditional log fire.

Specifications

The framed opening is 37" wide, 34-3/4" high and 16-1/4" deep, with 12" more depth for rear venting with a 90 degree elbow, and the fireplace itself is 36" wide, 34-5/16" high and 16-5/16" deep. Keep 1/2" of clearance at the back and sides, 32" from the top of the hood to the ceiling and 36" clear in front, and no raised hearth is needed. The metal front takes non-combustible facing only. Mantel clearance depends on the mantel's depth and is charted in Figure 10.2 on page 49 of the installation manual, with mantel legs and wall projections in Figures 10.3 to 10.5 on page 50. It takes a 1/2" gas line and an unswitched 110-120 VAC circuit.

Features

  • Six ceramic fiber logs and glowing embers standard
  • Full firescreen front and hood standard, so the fireplace needs no separate front
  • IntelliFire electronic ignition with battery backup for power outages
  • Up to 19,100 BTU/hr on natural gas or propane, with an adjustable flame height
  • Vents off the top or the rear, with both vent collars built in
  • Certified for bedrooms

Answers to common questions

What venting does the Mercury 32" need?

It vents off the top on 4" x 6-5/8" SLP or SLP-FLEX pipe, or off the rear on 5" x 8" DVP pipe, out through a wall or up through the roof. The fireplace is set up for one or the other at installation, and that cannot be changed later. Off the top it runs up to 60 ft straight up, up to 15 ft horizontal and 40 ft of combined run where elbows are used, with up to four 90 degree elbows. Off the rear it runs 24" straight out through a wall with no elbow, or up to 14-1/2 ft horizontal and 40 ft of combined run, with up to three 90 degree elbows. How far it can go sideways depends on the vertical rise before the first elbow, charted from page 19 of the installation manual, and SLP-FLEX cuts the total horizontal by 25%. It can also vent up an existing non-combustible chimney with the DV-46DVA-GCL adapter and LINK-DV30B kit, and it is approved for the three power vents listed on page 56 of the installation manual, with the PV-IPI-CK kit, a wire harness and an RC100, RC200 or RC300 control. Our team builds the vent package for your run; the approved parts are on page 56 of the installation manual and the termination clearances on pages 13 and 14.

What’s included, what’s required, and what’s optional?
  • Included in the box: Six ceramic fiber logs; Glowing embers; Full firescreen front and hood; Up to 19,100 BTU/hr on natural gas or propane; IntelliFire electronic ignition; Battery backup (two D cell batteries, not included); Tempered glass; Junction box, manual gas shut-off valve and flex connector, and 12 ft of control wire; Top vent collar, 4" x 6-5/8", and rear vent collar, 5" x 8".
  • Required to complete the installation, purchased separately: Venting - SLP pipe off the top or DVP pipe off the rear, and a wall or roof termination sized for your run (see pg 56 in the installation manual); Electrical - an unswitched 110-120 VAC circuit to the junction box; Gas Line - a 1/2" gas line to the shut-off valve.
  • Optional: A wall switch kit or remote control, a fan kit and a trim kit; beyond the venting and the gas and electrical connections, nothing else is required to complete the fireplace.
How is it turned on, and do I need a remote?

A wall switch, a wall thermostat or a remote control can turn it on and off, and the wall switch kit and remotes offered below are sold separately. The white wall switch kit comes with 20 ft of wire, and 12 ft of control wire comes with the fireplace. The SMART-STAT-HHT remote adds a temperature readout, thermostat mode and timer mode. The RCT-MLT-HHT remote adds fan speed and flame control as well. Without the RCT-MLT-HHT, the flame height is set with a knob on the gas valve inside the control cavity. Battery backup keeps it lighting in a power outage, though a fan and a remote do not run on battery.

How much heat does it give, and can I add a fan?

It runs up to 19,100 BTU/hr on natural gas or propane, down to 13,500 on natural gas and 14,500 on propane, and the flame height is adjustable. An optional 160 CFM fan kit comes as the fan alone or with a rheostat and temperature sensor. It is approved as supplemental room heat or as a decorative appliance, not as a primary heat source.

Can I put a mantel or a TV above it?

Combustible mantel clearance depends on how deep the mantel is: see Figure 10.2 on page 49 of the installation manual, with mantel legs and wall projections in Figures 10.3 to 10.5 on page 50. For a TV, Majestic publishes good faith guidelines for a TV above a mantel in Figure 3.4 on page 9 of the owner's manual, and wall surface temperatures above the opening in Figure 2.1 on page 6 of the installation manual. They are not a guarantee against your TV maker's temperature limits, so check those too. You can also send us your mantel depth. We're here to help!

Where can it be installed?

Inside a framed wall, on a flat wall, in a corner or in an alcove (Figure 3.4 on page 10 of the installation manual), with 1/2" of clearance at the back and sides, 32" from the top of the hood to the ceiling and 36" clear in front. It needs no raised hearth, and it sits on a hard metal or wood surface running its full width and depth, not directly on carpet, vinyl or tile. Adhesive vinyl flooring is not recommended. It is also certified for bedrooms, and may be installed as an OEM installation in a manufactured or mobile home. Rated input is for 0 to 2,000 ft and is reduced 4% per 1,000 ft above that in the USA.

What gas and electrical connections does it need?

On natural gas or propane it takes a 1/2" gas line to the shut-off valve and flex connector that come with it, plus an unswitched 110-120 VAC circuit to the junction box. Inlet pressure is 5" to 10" w.c. on natural gas and 11" to 13" w.c. on propane. It is built for natural gas, and choosing Propane above adds the LP conversion kit, which a qualified service technician installs.

Does buying from The Torch Guys affect my Majestic warranty?

No. The Torch Guys is an authorized Majestic dealer, and the warranty covers fireplaces bought from one. On a gas fireplace the firebox and heat exchanger carry 20 years on parts and 3 on labor, burners, logs and metal or fiber refractory 10 years on parts and 1 on labor, electrical components 2 years, and all other parts 1 year. We will help you with any claim.

  • Model MERC32IN (natural gas) / MERC32IN + LPK-3732 (propane)
  • Series Majestic Mercury
  • Fuel Type Natural Gas or Propane (choose above)
  • Venting Type Direct vent, top vent 4 in. / 6-5/8 in. SLP or rear vent 5 in. / 8 in. DVP
  • Ignition Type IntelliFire intermittent pilot, with battery backup
  • BTU (Natural Gas) 19,100 BTU/hr high / 13,500 low
  • BTU (Propane) 19,100 BTU/hr high / 14,500 low
  • Viewing Area 27-3/16" W x 18-1/16" H (glass size)
  • Unit Width 36"
  • Unit Height 34-5/16"
  • Unit Depth 16-5/16"
  • Framing Width 37"
  • Framing Height 34-3/4"
  • Framing Depth 16-1/4" (add 12" for rear vent with a 90 degree elbow)
  • Clearance (Sides) 1/2"

Shipping & Returns

Free curbside freight delivery on every order over $399. Inspect the shipment before signing and note any damage on the delivery receipt — freight damage claims must be reported within 5 business days. Most items can be returned within 30 days of delivery as long as the product hasn't been installed, is in the same condition you received it, and all original packaging is intact. Return shipping and the original outbound freight cost are deducted from the refund, and a manufacturer restocking fee may apply. Custom and made-to-order products are final sale. Cancellations are free any time before shipment (custom orders excepted). Threshold and white-glove delivery upgrades are available — ask our team.

Full shipping policy · Full return policy · Questions? Call (410) 324-6322 — when you call, we answer.

Warranty

In the unlikely event your product experiences a defect, our technical team will guide you through the manufacturer’s warranty process. Here is a general outline of what to expect.

Due to the technical nature of our products, the manufacturer must perform troubleshooting to process a warranty claim. Your installer will need to troubleshoot the problem on-site while working in tandem with our technical team. If troubleshooting leads to what The Torch Guys deems as a defective part, we will submit a warranty claim to the manufacturer on your behalf. Before we submit the claim, we will ask you to review the terms and confirm your consent to proceed.

Once the claim is submitted, the manufacturer will review it and either approve or deny it. If they have all the information and accept the claim, your warranty replacement part(s) will begin processing for shipment. If, for any reason, the claim is denied or we need more information, we will notify you as soon as possible.

All warranties are processed as exchanges. You can expect to receive a prepaid return label for the defective part(s), which must be returned within 30 days of receiving the warranty replacement(s).

Warranty claims can take anywhere from 1-4 weeks to process, depending on the season. Given the length of time claims can take, we recommend you fire up your unit in late summer/early fall to ensure your existing fireplace is in good working order for the winter season.