Majestic Meridian 36" Direct Vent Gas Fireplace
What's Included?
Here's what ships in the box and what you'll choose above before checkout. Not sure what you need? Call us at (410) 324-6322 and our team will spec the right setup.
Here's what ships in the box and what you'll choose above before checkout. Not sure what you need? Call us at (410) 324-6322 and our team will spec the right setup.
The Majestic Meridian 36" is a direct vent gas fireplace with IntelliFire Touch electronic ignition and battery backup: up to 30,000 BTU/hr on natural gas or 29,000 on propane, a 42" wide, 40-1/8" high and 22" deep rough opening and top or rear venting, from $2,899. A decorative front and a log set finish it, with five front styles and oak or birch logs to choose from.
Choose the Meridian 36" if you want a log fire you can style: oak or birch logs, inside fit or overlap fronts, and optional brick or glass interior panels. With only 1/2" of clearance at the back and sides and no raised hearth, it frames tightly into a wall, and it is certified for bedrooms and approved for protected outdoor rooms.
It is not right for you if you are looking for a long, linear flame over a bed of glass. The Meridian 36" is a traditional log fire, with a set of six logs over a ceramic fiber burner top and glowing embers.
The rough opening is 42" wide, 40-1/8" high and 22" deep, with 12" more depth for rear venting with one 90 degree elbow, and the fireplace itself is 41" wide, 40-7/8" high and 16" deep. Keep 1/2" of clearance at the back and sides and 32" from the top of the opening to the ceiling, and no raised hearth is needed. The non-combustible board is factory-installed; combustible facing at the top and sides can be up to 1/2" thick, and non-combustible finish can run up to 6" thick, depending on the front. Mantel clearance depends on the mantel's depth and is charted in Figure 10.4 on page 67 of the installation manual, with a separate chart in Figure 10.5 for the Passive Heat Kit. It takes a 1/2" gas line and an unswitched 110-120 VAC circuit.
The two Meridian sizes share the IntelliFire Touch ignition, the same five front styles, oak or birch logs and top or rear venting. The 36" runs 30,000 BTU/hr on natural gas and frames 42" wide, the 42" runs 35,000 BTU/hr and frames 49" wide. This 36" starts from $2,899 and the 42" from $3,759.
It vents off the top or the rear on 8" DVP pipe, or on SLP pipe with an adapter, out through a wall or up through the roof. Off the top it can run up to 60 ft straight up, and with one elbow 1/2 ft up allows 6 ft out; 1 ft up allows 11 ft out; 1-1/2 ft up allows 18 ft out; 2 ft up allows 25 ft out, with 40 ft of combined run at most. Off the rear it goes 16 in. straight through the wall, up to 20 ft horizontal with two elbows, or up to 8 ft horizontal with a roof termination. It can also vent up an existing masonry or factory-built chimney with the DV-46DVA-GCL adapter and LINK-DV30B liner kit, and it is approved for the PVLP-SLP low profile and PVV-SLP vertical power vents and the Power Vent Inline, with the wire harness and IFT-RC400 remote. Our team builds the vent package for your run; the approved parts are on page 77 of the installation manual and the termination clearances on pages 27 to 29.
Every front carries a built-in mesh barrier. Essence and Essence with ClearVue mesh fit inside the opening, so the wall finish can run up to the fireplace with non-combustible material up to 6 in. thick. Ventura, Manor and Ensemble overlap non-combustible finish up to 1 in. thick, or, with the finishing strips that ship with the fireplace, go in as inside fit over non-combustible finish 1 to 6 in. thick. The interior is matte black as standard. Traditional or Herringbone Tavern Brown brick, Tranquil Greige herringbone brick, Castle Stone brick and 2-sided reflective black and matte glass panels are all optional.
A remote is optional. The control module has a switch for on, off or remote. Set to on, it runs at the high flame setting with no adjustment. Set to remote, it answers a wired wall switch, the IFT-RC150 wireless wall switch or the IFT-RC400 remote. Adjusting the flame takes the IFT-RC400 or the IFT-WFM Wi-Fi module. Battery backup keeps it lighting in a power outage, though a fan does not run on battery, and a safety feature shuts it down after 9 hours with no command from a remote.
Yes, with planning. Without a passive heat kit, Majestic's good faith guideline is 20" from the top of the opening to the bottom of the TV, with a mantel 2" to 3" below the TV and 3" past it (Figure 2.3 on page 9 of the installation manual). The optional Passive Heat Kit moves heat out through a discharge opening, and with no fan no mantel is needed: 12" from the opening to the bottom of the TV and 4" from the top of the TV to the discharge opening. With Passive Heat and a fan a mantel is required (Figure 2.4 on page 10). The kit goes in with the fireplace. Always stay within your TV maker's own temperature limits.
Inside a framed wall, with 1/2" of clearance at the back and sides, 32" from the top of the opening to the ceiling and 36" clear in front. It can sit on a combustible floor with no raised hearth, as long as flooring stays below the top of the bottom surround. It is certified for bedrooms and bedsitting rooms, may be installed as an OEM installation in a manufactured or mobile home, and is approved for protected outdoor rooms, patios and decks kept out of direct water. Adhesive vinyl flooring is not recommended. Rated input is for 0 to 2,000 ft and is reduced 4% per 1,000 ft above that in the USA.
Natural gas and propane are separate models, so choose the one that matches your house. It takes a 1/2" gas line to the T-handle shut-off valve and flex connector on the fireplace, with a recommended inlet pressure of 7.0" w.c. on natural gas and 12.0" w.c. on propane, plus an unswitched 110-120 VAC circuit wired with 14-2 AWG with ground to the junction box.
No. The Torch Guys is an authorized Majestic dealer, and the warranty covers fireplaces bought from one. On a gas fireplace the firebox and heat exchanger carry 20 years on parts and 3 on labor, burners, logs and metal or fiber refractory 10 years on parts and 1 on labor, electrical components and glass liner panels 2 years, and all other parts 1 year. We will help you with any claim.