
True North TN20 Wood Insert
What's Included?
Here's what ships in the box and what you'll choose above before checkout. Not sure what you need? Call us at (410) 324-6322 and our team will spec the right setup.

Here's what ships in the box and what you'll choose above before checkout. Not sure what you need? Call us at (410) 324-6322 and our team will spec the right setup.
55,000 BTU/hr peak output from a 2.0 cu ft firebox that takes 18" logs, in a masonry fireplace opening as small as 29" wide, 20-1/4" high and 18" deep. The True North TN20 Insert is an EPA 2020 certified, catalytic-free wood insert with a gasketed cast iron door, air-wash ceramic glass, a built-in variable-speed blower, a 6" flue collar and its 38" x 27" surround in the box, rated at 78% LHV efficiency and 1.6 g/hr. It starts from $2,218 and carries True North's 3-year parts warranty on the firebox, castings and glass.
Choose the TN20 Insert if you want to turn an open masonry fireplace into a heater for a small to medium space without rebuilding it: it slides into an opening 18" deep, the surround and blower come with it, and the blower pushes heat into the room at the speed you set. If your fireplace face is larger than the 38" x 27" surround, add the 48" x 32" oversize backing plate or the 2" deep recess extension above.
It is not right for a factory-built fireplace — it installs only in a masonry wood-burning fireplace with a masonry chimney, on its own 6" listed stainless steel liner, and the opening must be at least 29" wide at the front, 22" at the back, 20-1/4" high and 18" deep. It burns cord wood with the door closed; if you want an open fire to sit beside, this is not the insert.
The masonry opening must be at least 29" wide at the front, 22" wide at the back, 20-1/4" high and 18" deep, and the chimney should be at least 15 ft tall. Side-wall and side-facing clearances are in Figure 3 on page 11 and on the rating label on page 25 of the installation manual; a mantel or top facing up to 12" deep sits at least 15" above the top of the firebox, and the ceiling is at least 54" above the base of the insert. In the USA the hearth extends 16" in front and 8" beyond each side of the opening and sits 1" above a combustible floor, or extends 21" in front if flush, and a combustible floor in front is protected from embers 16" out and 8" to the sides (18" in front in Canada). It vents through a listed 6" stainless steel liner, and the blower runs on 115 V, 60 Hz from a grounded outlet.
It needs a listed 6" stainless steel rigid or flexible chimney liner — UL 1777 in the USA — joined to the insert's flue collar with a stove connector, and the liner is not in the box; our team builds the vent package for your chimney. The full liner runs to the top of the chimney with a top flashing and rain cap; it is required in Canada and is the connection Pacific Energy recommends as the safest and best-drafting. In the USA a direct flue connection is also approved, with the liner run to the first chimney flue tile and the throat sealed with non-combustible material, and local codes may then require a clean-out door. The chimney should be at least 15 ft tall, the fireplace damper is locked open or removed, and the flue may serve no other appliance.
It fits an approved masonry wood-burning fireplace with an opening at least 29" wide at the front, 22" wide at the back, 20-1/4" high and 18" deep, and it is never installed in a factory-built fireplace. The fireplace is inspected and repaired first, the chimney cleaned, and the damper locked open or removed; bricks and mortar stay in place. The 38" x 27" surround in the box covers the gap around the insert; for a larger fireplace face, add the 48" x 32" oversize backing plate or the 46" x 31" deep recess extension above. Leveling bolts in the box steady it on an uneven hearth.
The side-wall and side-facing clearances are in Figure 3 on page 11 and on the rating label on page 25 of the installation manual. A mantel or top facing up to 12" deep sits at least 15" above the top of the firebox, and the ceiling is at least 54" above the base of the insert. In the USA the fireplace hearth extends at least 16" in front and 8" beyond each side of the opening and sits 1" above a combustible floor, or extends 21" in front if it is flush; a combustible floor in front is protected from embers by non-combustible material 16" out and 8" to the sides. In Canada the hearth extends 16" in front and the ember protection 18".
Not necessarily — whichever options you choose, the insert can draw combustion air from the room once the cover plate under the ash lip is removed, though the room may need make-up air from outside. It can also take outside air through the fireplace's ash clean-out, with a rodent screen in place of its cover. Your local building code decides whether outside air is required.
No. The TN20 Insert is not designed for open-door burning; the loading door stays closed while it burns and opens only to load wood. It burns seasoned cord wood laid directly on the firebricks, never on a grate or andirons.
No. The warranty is True North's and covers every configuration on this page — 3 years on parts (1 year labour) for the firebox, castings and glass, 1 year on parts and labour for the blower's electrical components and switches, and 1 year on parts for gaskets, paint, bricks and the baffle parts, with a one-time replacement limit on each part. Keep your dated bill of sale, because a claim needs it along with the model name and serial number, and register the insert at truenorthstoves.com/register; The Torch Guys will help you with any claim. It covers the original purchaser in normal residential use and requires installation by an authorized qualified technician.