A 32" steel log with a 150,000 BTU/hr UL150 linear CROSSFIRE® brass burner built into it, mounted on a 38" x 10" aluminum plate and sold as one piece. It runs on natural gas or propane with both adapters in the box, lights by hand through a lighting opening at either end of the log, and sits on a bed of fire glass or lava rock inside a non-combustible enclosure you build. The steel is meant to patina with use and weather. Designed, engineered and assembled in Colorado, USA. $1,488.
Choose it if you want a steel log fire in a custom pit or outdoor fireplace without matching a log set to a burner yourself. The burner, the log that hides it and the plate that carries both arrive as one part, sized to each other by Warming Trends, so your installer builds the ledge, runs the gas to a key valve and lays the media bed, and the flame comes up through the log where it was designed to.
The log is 32" long and the aluminum plate under it measures 38" x 10". The UL150 burner inside is 29-3/4" long and 2-5/8" tall and is rated at 150,000 BTU/hr on either fuel; the match-lit inlet pressure is 3.5" to 7.0" W.C. on natural gas and 11.0" to 13.0" W.C. on propane. Keep 36" from the top of the flame to anything combustible to the sides and 84" overhead, recess the assembly 4" to 6" below the top of the enclosure, rest the plate on a ledge of block, brick or metal collars rather than on a valve, leave the cavity below it empty, and vent the enclosure with at least 18 square inches on each of two opposing sides. The media bed goes in first, about two inches wider and longer than the log; the log is pressed into it with the burner centered underneath and the jet nearest the lighting end left exposed. Outdoor use only.
How do I light it?
By hand, with a long-reach lighter. The log has a lighting opening at each end. With the main gas supply open and the key valve still closed, check the pit for leaves and debris, put the lighter through the opening at the jet tip nearest that end, then open the key valve slightly to the left so a small flow of gas reaches the burner and that jet lights. Open the valve further and the rest of the jets catch. Set the flame height with the key valve. To shut down, turn the key to the right, make sure the flame is out, close the tank if you are on propane, and cover the feature once it has cooled. Warming Trends recommends an ignition system above 300,000 BTU; at 150,000 BTU the FireStorm is a match-lit log.
Natural gas or propane?
Either. The UL150 is a CROSSFIRE 2.0 burner and ships with both a natural gas adapter and a propane adapter. Your installer fits the one for your fuel at the coupling under the plate before first use and keeps the other in case the fuel or the location ever changes. The inlet pressure at the burner needs to land between 3.5" and 7.0" W.C. on natural gas or 11.0" and 13.0" W.C. on propane. For a propane tank rather than a plumbed line, Warming Trends lists a FireStorm LPRH kit, its liquid propane regulator hose for the FireStorm.
What’s included, what’s required, and what’s optional?
-
Included in the box: The 32" FireStorm steel log with the UL150 CROSSFIRE® brass burner integrated into it, mounted on a 38" x 10" aluminum plate; Natural gas and propane adapters for the burner's coupling.
-
Required to complete the installation, purchased separately: A match-lit flex line and key valve kit: Warming Trends' FK1 (36" whistle-free flex line, flared fittings, 3/4" key valve, 3" and 12" keys and nipple) connects the coupling under the plate to your gas supply; Approved media for the bed the log sits on: fire glass or lava rock 1/2" or larger, enough for a flat bed about two inches wider and longer than the log; A natural gas or propane supply delivering 3.5" to 7.0" W.C. (natural gas) or 11.0" to 13.0" W.C. (propane) at the burner, with a shutoff outside the feature, installed by a qualified gas professional; A non-combustible enclosure built on a level surface, with a support ledge for the plate, 18 sq in of venting on two opposing sides, the assembly recessed 4" to 6" below the cap, and 36" side / 84" overhead clearance to anything combustible.
-
Optional: Warming Trends' FireStorm LPRH kit (a propane regulator hose for running from a propane tank) and a waterproof cover for the feature when it is cold — the log burns without either.
Does it come with lava rock or fire glass?
No, and the media is not decoration here: it is the bed the log sits on. Install fire-rated media made for outdoor fire features, 1/2" or larger, placed on the plate rather than poured over the burner, as a flat bed about two inches wider and longer than the log, then set the log over the burner with the burner centered underneath, one end near the key valve, and press it down so it sits level. Adjust the media so the jet tip nearest the lighting end stays exposed, and never bury the burner more than 1/2" above the jets. If the media is wet when you light it, give it 30 minutes to dry out and watch from a distance until any popping stops.
Why is the log rusting?
Because it is supposed to. The FireStorm is bare steel, and Warming Trends designs it to patina: a layer of rust or oxidation forms over time, the color shifts with heat and weather, and the log looks more like a log the longer it burns. Each one develops its own pattern. The log may also have sharp edges, so wear gloves when you handle it. Soot can collect along the openings; once a year, or sooner if the flame starts to suffer, let it cool, lift it off, and rinse it with water or brush it with a plastic brush, keeping water and soot out of the burner.
Where can I install it?
Outdoors only, in a non-combustible enclosure on a stable, level surface. Keep 36" from the top of the flame to any combustible structure or material to the sides and 84" overhead, and recess the assembly 4" to 6" below the top of the enclosure so wind does not reach the flame. The plate carries the burner's weight and rests on a ledge of block, brick or metal collars, never on a valve; the cavity below stays empty; the enclosure gets at least 18 square inches of venting on each of two opposing sides; and the capstone must not overhang the plate's outer edge unless you build in an access door. Mount the key valve below the plate through the side wall, or remotely, and orient the log so one end is near it. Installation and service are by a qualified installer or gas professional, to local code.
How is this different from Warming Trends' steel log sets?
The steel log sets (18", 24", 30" and 36", or a custom handcrafted set by quote) are logs only, made to sit over a burner you buy separately. The FireStorm is the one steel log Warming Trends sells with the burner and plate built in: the UL150, which the company also sells on its own and in kits with a flex line and a 38" x 8" plate, comes integrated into the 32" log on a 38" x 10" plate, so there is no matching to do.
How does the warranty work if something goes wrong?
The CROSSFIRE brass burner inside the log carries Warming Trends' lifetime full warranty, from the date of purchase and regardless of ownership, with repair or exchange at no charge. The Torch Guys handles it for you: we register the product and, if you ever need to claim, we deal with the manufacturer on your behalf rather than handing you a phone number. Keep your invoice and the model number, FSLS32; we hold the rest on file.