Napoleon Elevation X 42" Direct Vent Fireplace

It is a direct vent fireplace on a 5" exhaust / 8" air-intake pipe off the top of the unit, run out through a wall or up through the roof: up to 20 ft horizontally and up to 40 ft vertically. Use one brand of pipe throughout — Napoleon (Wolf Steel), Metal-Fab, BDM, Simpson Dura-Vent or Selkirk Direct Temp — and do not mix rigid and flexible pipe. A wall termination uses Napoleon's round GD422R-2 terminal or the Silhouette terminal kit; roof kits cover pitched and flat roofs. The vent run and termination are ordered separately and sized to your installation, and the outside terminal clearances are listed on page 16 of the installation manual. It is also certified for a power vent kit.

• Included in the box: Electronic pilot-on-demand ignition with the ProFlame 2 remote control; eFIRE Bluetooth controller; Two heat-circulating blowers with six speeds; Night Light and electric ember bed lighting; 5 mm ceramic glass door with full-view safety barrier screen; Header shield, nailing tabs, vent insulation sleeve and firestop.
• Required to complete the installation, purchased separately: Interior Panel - the panels that line the firebox, in porcelain, glass, brick or ledgestone; Log Set - the high-definition logs with glowing and charcoal embers; Non-Combustible Board Kit - the cement board panels that finish the face around the fireplace; not needed if you add the Dynamic Heat Control or Ducted Heat Management kit (see pg 18 in the installation manual); Venting - 5" / 8" direct vent pipe and a wall or roof termination sized for your run (see pg 13 in the installation manual); Electrical - a grounded 115 V supply, hard-wired to the fireplace; Gas Line - a 1/2" gas supply to the fireplace's shut-off valve.
• Optional: A vertical or external wall venting package, heat management (Dynamic Heat Control, Dynamic Heat Control Plus, Ducted Heat Management or the Hot Air Distribution Kit), a power vent adaptor kit, decorative fronts, finishing trims and the Wall Mount Control — the fireplace operates fully without any of them.

Yes, with planning. Napoleon draws the minimum TV clearances above the Elevation X — flush with a mantel, recessed, and recessed with a protrusion; a flush installation without a mantel is crossed out — on page 43 of the installation manual, and the mantel clearances on page 44. Adding the optional Dynamic Heat Control system moves heat away from the fireplace, lowers the wall temperature above it and reduces the mantel clearances, which is what it is designed for when a TV sits directly above; it goes in while the fireplace is framed, before the venting and gas. Always stay within your TV maker's own temperature limits.

Indoors, including bedrooms, bathrooms and bed-sitting rooms, and it is certified for mobile and manufactured homes where local codes allow (fastened in place). It is rated to 4,500 ft, with the input reduced above that. Keep furniture and other objects at least 48" from the front, and do not run it below freezing.

A 1/2" natural gas or propane line to the fireplace's flex connector and shut-off valve, installed and tested before the wall is finished — natural gas at 4.5" to 7" w.c. inlet pressure, propane at 11" to 13" w.c. Electrically it is hard-wired to a grounded 115 V, 60 Hz supply; with batteries in the receiver the flame still works during a power failure, though the blowers and Night Light do not. It can be converted between natural gas and propane with Napoleon's certified conversion kit.

No. The Torch Guys is an authorized Napoleon dealer, so the President's Lifetime Limited Warranty applies in full, and we file claims with Napoleon for you. The firebox, burner, PHAZER logs and embers and the ceramic glass (against heat breakage) are covered for as long as you own the fireplace — parts free for the first 10 years, then at half of retail; blowers, valves, remotes and other electrical parts and the labour are covered for the first year. Coverage starts on the installation date.